Sony Support

Firmware update Ver.2.00 for HDR-AS100V (Macintosh)

Add Live Streaming and new functions for still image shooting mode.

    Applicable Models
    About this download
    System Requirements
    Download
    Install

    Applicable Models

    This information is for the following models:
    • HDR-AS100V

    About this download

    System Requirements

    Operating Systems

    The latest version of the firmware update is compatible with the following Macintosh versions:
    • Mac OS X v.10.6 ~ 10.10

    Computer hardware

    The latest version of the firmware update is compatible with the following hardware:
    • CPU: Intel processor*
      *Core Solo and Core Duo processors are no longer supported
    • Hard disk space: 200MB or more
    • RAM: 512MB or more
      Note: Please close all other application software before updating the firmware.
    • Power source for the camera
      • Fully charged rechargeable battery pack NP-BX1
        Note: The update can be performed only when the remaining battery level is (three marks) or more. We recommend that you use a fully charged battery.
    • USB cable supplied with the camera

      Note: Update functionality is not guaranteed with any other USB cable.

    Download

    Important notes:

    • When performing the firmware update, please use a fully charged rechargeable battery pack NP-BX1.
    • Do not remove the battery during the update; otherwise, the camera may become inoperable due to the sudden power shutdown.
    • Remove the memory card from the camera beforehand.

    How to download the firmware updater:

    1. Make sure that you are logged on as a user with administrative rights.
    2. At the bottom of the page, read the disclaimer and agree to the terms and conditions by clicking on the checkbox. Then, click on the Download button.
    3. The download of the [Update_HDRAS100VV200.dmg] file will start.
    4. Save the file to the desktop of your computer (recommended).

    Install

    Once the file has downloaded successfully, you're ready to install the Firmware update Ver.2.00 for HDR-AS100V.

    Step 1: Start up the Firmware Updater

    1. Close all currently running programs on your computer.
    2. Double-click the [Update_HDRAS100VV200.dmg] file you downloaded. Do not connect the camera at this point.
    3. [Update_HDRAS100VV200] is expanded.
    4. Double-click the [FirmwareUpdater] icon.
    5. To load a kernel extension, the message prompts you to allow the application to make changes. Type the password for the administrative account.



    6. Firmware Updater starts up.



    7. Remove the memory card from the camera beforehand. Connect the camera to the computer with the supplied USB cable.
      Note: USB Mode appears on the LCD monitor of the camera.
    8. After confirming the above, click Next on the Firmware Updater window. Figure 1 appears on the Firmware Updater window, and Figure 2 appears on the LCD screen of the camera.Note: From now on, never turn off the camera until the firmware update is completed.
      Figure 1Figure 2

    9. After confirming the screens on Figures 1 and 2, click Next. The current version and the version after the update appear on the lower left part of the screen. (Figure 3)
    10. After confirming [Current version] is [Ver.1.00], clickNext.

      If [Current version] is [Ver.2.00], the update is not required. According to the message, stop the USB connection and click Finish. Turn off the camera, remove the battery pack, reinsert the battery and turn on the camera.
      Figure 3

    11. The screen on Figure 4 appears.

      Figure 4


    12. Press the [ENTER] button to execute the reset of the camera.


      Note: The screen turns off when the [ENTER] button is pressed. Please proceed to the next step.

    13. Click Next on the Firmware Updater window (Figure 4).
    14. After resetting, reconnection of the camera is verified, and the screen on Figure 5 appears.
    15. Click Run to start the update. The progress bar appears while updating(approximately 10 minutes).
      Note:Never turn off the camera nor disconnect the USB cable while updating.

      Figure 5


    16. When the update is completed, the screen on Figure 6 appears. Click Finish and disconnect the USB cable.

      Figure 6


    17. Turn off the camera, remove the battery pack, reinsert the battery and turn on the camera again.

      Note: In order to use Live Streaming function, it is required to download additional PC software "Network Setting Tool" to input the settings to the camera. For details, please refer to "Streaming videos on USTREAM" http://support.d-imaging.sony.co.jp/www/download/apps/nst/mac/en.html.

    Step 2: Confirm the firmware version of your camera is Ver.2.00.

    1. Press the NEXT button to display [LIVE]. If [LIVE] appears then the firmware version is Ver.2.00.